Güncel Gönderiler: Mühendislik Fakültesi
Toplam kayıt 1048, listelenen: 281-300
-
Probabilistic power flow analysis of power systems with PV and wind using monte carlo method
(Institute of Electrical and Electronics Engineers Inc., 2023)With the increase in renewable energy systems, the increasing uncertainties in power systems make the analysis with deterministic power flow method insufficient. Probabilistic load flow allows us to see the distribution ... -
Enhancing filtration performance of submicron particle filter media through bimodal structural design
(Wiley, 2023)Depth filtration is a widely utilized mechanism for submicron aerosol filtration using disposable filter cartridges and facemasks. The filter media should be carefully engineered to reach high filtration efficiency and ... -
Mechanical, energy evolution, damage and microstructural behavior of cemented tailings-rock fill considering rock content and size effects
(Elsevier, 2024)Cemented tailings-rock fill (CTRF) is crucial for engineering intention and durability of re-filled stopes in deep underground mines. The current work examined the effects of fragment contents and sizes on the mechanical, ... -
New modified carrier-based level-shifted PWM control for NPC rectifiers considered for implementation in EV fast chargers
(TUBİTAK Scientific & Technical Research Council Turkey, 2023)In this study, the aim is to evaluate three-phase (3ϕ) AC/DC neutral point-clamped (NPC) power factor-corrected (PFC) multilevel converter performance for electric vehicle (EV) fast chargers. Power factor correction for ... -
Entransy-based environmental and life cycle cost analysis to determine optimum insulation thickness: Effect of the fuel sources
(Gazi Universitesi, 2024)In this study, the influence of fuel sources on entransy-based environmental impact and life cycle cost (LCC) analysis while determining the optimum insulation thickness (OIT) has been investigated. Analyses are carried ... -
Machine learning driven optimization and parameter selection of multi-surface HTS Maglev
(Elsevier, 2024)This research aims to tackle the challenges posed by precise force measurement for high temperature superconducting (HTS) Maglev systems, including mechanical constraints, step motor limitations, and sensor resolutions. ... -
Determination of novel SARS-CoV-2 inhibitors by combination of machine learning and molecular modeling methods
(Bentham Science, 2023)Introduction: Within the scope of the project, this study aimed to find novel inhibitors by combining computational methods. In order to design inhibitors, it was aimed to produce molecules similar to the RdRp inhibitor ... -
Monitoring sediment transport in certain harbor launches in the southeastern black sea
(Multidisciplinary Digital Publishing Institute (MDPI), 2023)Abstract: The problem of shoaling on coastal structures is the result of an event that occurs as part of the natural cycle. In cases where shoaling cannot be detected or prevented, various economic and operational problems ... -
Mechanical properties of Al-9Si-0.6Mg-0.1Sr alloy processed by successive hot and cold multi-directional forging
(Springer, 2023)In this study, the effect of successive hot and cold multi-directional forging (MDF) on the mechanical properties of the Al-9Si-0.6Mg-0.1Sr alloy was explored. The alloy was first homogenized and then forged at 200°C from ... -
Effect of inlet temperature on flow boiling behavior of expanding micro-pin-fin type heat sinks
(Elsevier, 2023)Heat sinks that cool electronic systems through flow boiling are exposed to working fluids at different inlet temperature. Therefore, in the present study, influence of inlet temperature on boiling performance of a ... -
Development and characterization of a new solid polymer electrolyte for supercapacitor device
(Hindawi, 2023)In this study, solid polymer electrolytes (SPEs) are based on methylcellulose (MC) used as a polymer host and sodium iodide (NaI) as a dopant. The SPE films are developed using different contents of ethyl carbonate (EC) ... -
Upstream vortices of a sluice gate: an experimental and numerical study
(IWA Publishing, 2023)This paper aims to explore the effects of a sill under a standard sluice gate on the development of the intake vortices. In total, 200 experiments were carried out. Sills with different shapes and widths were considered ... -
Identifcation of goaf instability under blasting disturbance using microseismic monitoring technology
(Springer, 2023)Micro-seismic (MS) technique can be used to appreciate rock failure process and severity of damage by quantifying micro-earthquakes in terms of time, location, grade, and energy release. Based on 3D laser detection and ... -
Analyzing the microstructure of cemented fills adding polypropylene-glass fibers with X-ray micro-computed tomography
(Elsevier, 2023)Fiber reinforced cementitious tailings backfill (FRCTB) is progressively employed in mining industry due to its high strength/stiffness-to-weight ratio. However, the wide use of the FRCTB technique requires further study ... -
Comparative study by the finite element method of three activities of a wearer of total hip prosthesis during the postoperative period
(Techno-Press, 2023)The postoperative period for a carrier of total hip prosthesis (THP), especially in the first months, remains the most difficult period for a patient after each operation, even if traumatologist surgeons want the relief ... -
Triple-effect new generation drying technique
(Elsevier, 2023)This paper introduces the triple-effect new generation drying technique that is defined as simultaneously swirling flow-fluidized bed-infrared drying process. It aims to perform the conceptual design of this innovative ... -
Effect of aluminosilicate precursors and curing regime on physico-mechanical durability and microstructural characteristics of coral geopolymers (Cor-Geo): Cleaner production for coral islands
(Elsevier, 2023)This study investigated the mechanical, durability, microstructure, carbon footprint and cost characteristics of new-generation metakaolin-based geopolymer composites. Instead of GBFS, 25 % metakaolin was used, and 25 ... -
Comparative investigation of different types of expanding micro-pin-fin heat sinks at low mass flux
(Elsevier, 2023)Expansion of cross-sectional area of flow passages in micro-pin-fin heat sinks provides advantages due to suppression of bubble-confinement problem. However, low mass flux in addition to orientation of fins and existence ... -
Effects of WEDM and AWJ cutting methods on induction motor efficiency and total magnetic losses: Experimental design and response surface methodology
(Elsevier, 2023)In this study, the effect of cutting electrical steel laminations using abrasive water jet (AWJ) and wire electrical discharge machining (WEDM) techniques on 5.5 kW induction motor efficiency (MEfficiency) and total magnetic ... -
Polymer shape effect on damage evolution, internal defects and crack propagation of 3D-printed polymer-based cementitious backfill
(Elsevier, 2023)The strength property and damage mode of cementitious tailings backfill (CTB) are governed by its structural characteristics in the presence of the microstructure/internal defect effects. However, this correlation is still ...