Başlık için Makine Mühendisliği Bölümü Koleksiyonu listeleme
Toplam kayıt 275, listelenen: 33-52
-
Design, modelling, environmental, economic and performance analysis of parabolic trough solar collector (PTC) based cogeneration systems assisted by thermoelectric generators (TEGs)
(Elsevier, 2024)Concentrating solar power systems (CSP) is a very efficient technology for clean and renewable energy production. It basically works on the principle of focusing the sun's rays with the help of a reflective surface. There ... -
Detection, location, and diagnosis of different faults in large solar PV system-a review
(Oxford University Press, 2023)Over the past decade, the significance of solar photovoltaic (PV) system has played a major role due to the rapid growth in the solar PV industry. Reliability, efficiency and safety of solar PV systems can be enhanced by ... -
Determination of delamination in drilling of carbon fiber reinforced carbon matrix composites/Al 6013-T651 stacks
(Elsevier Sci Ltd, 2020)Delamination at the hole entrance and exit during drilling of the FRPs composites adversely affects the hole surface quality and engineering properties of this material. in this study, delamination occurrence in hole ... -
Development of a new curve equation representing thin layer drying process
(Taylor & Francis Ltd., 2023)In this study, a new model for thin-layer drying process was developed, tested, and verified by using data from the literature and compared. In this regard, the required data were collected from the experiments of green ... -
Development of optical, microstructural and mechanical properties of porcelain stonewares
(International Institute for the Science of Sintering, 2021)New production systems developed in recent years made it possible to improve different aesthetic appearance and large sizes for porcelain stonewares. In order to produce these tiles, optical and mechanical properties of ... -
Dry cutting: A sustainable machining technology
(Elsevier, 2021)Conventional cutting fluids with flood cooling are used to reduce the heat generation during machining but at the cost of environmental degradation. The hydrocarbon-based conventional cutting fluids are harmful to the ... -
Düşük dolum oranında ikili karışımlarla yüklü üniform olmayan atımlı ısı borusunun deneysel incelenmesi
(Düzce Üniversitesi, 2021)Bu çalışmada, düşük bir dolum oranında ikili karışımlarla yüklü, üniform olmayan kanal profiline sahip düz plakalı kapalı döngülü atımlı bir ısı borusunun ısıl performansı ve akış davranışı deneysel olarak incelenmiştir ... -
Dynamo script and a BIM-based process for measuring embodied carbon in buildings during the design phase
(Oxford University Press, 2023)In recent years, worldwide efforts have been made towards reducing energy use and emissions, which have a variety of impacts such as contributing to climate change. Hence, environmental analysis in the construction sector ... -
The effect of ABS fraction on the fatigue behavior of PMMA/ABS polymer blends
(Elsevier, 2022)This paper aims to examine the fatigue behavior of the Poly(methyl methacrylate)/ Acrylonitrile-butadiene-styrene (PMMA/ABS) polymer blends by means of experimental studies. For the material characterization of the blends, ... -
Effect of air change rate on particle dispersion from inlet opening under varying particle source strengths
(Taylor and Francis Ltd., 2020)In this study, effect of air change rate (air change per hour–ACH) on indoor particle dispersion and deposition in a ventilated room is investigated. A reduced-scale model is designed to conduct experiments. Numerical ... -
Effect of air exhaust location on surgical site particle distribution in an operating room
(Tsinghua Univ Press, 2020)This study investigates effect of exhaust outlet location on airflow and particle distribution in an operating room with laminar ventilation system (LAF) via computational fluid dynamics (CFD). Four different exhaust opening ... -
Effect of arc re-melting on microstructure, mechanical and tribological properties of commercial 390A alloy
(Elsevier, 2021)To investigate the effect of the arc re-melting on the microstructure, mechanical and tribological properties of the 390A alloy, its ingot produced by the conventional induction melting method was subjected to the arc ... -
Effect of boronizing on operating stability of steel AISI 304L under erosion impact of hard particles
(Springer, 2021)The effect of solid boronizing at 950 degrees C for 2 and 4 h on the phase composition, microstructure, hardness and abrasive wear of steel AISI 304L is studied under the impact of a flow of hard particles. The boronized ... -
Effect of case depths on corrosion properties of hard anodic oxidized A356 aluminum alloy
(World Stientific Publishing, 2023)In this work, A356 alloy samples having a dimension of 4x20x20mm were coated by hard anodic oxidation method at eight different thicknesses up to similar to 80 mu m. The sample surfaces and longitudinal section of these ... -
Effect of different zinc contents on the structural, mechanical and tribological properties of EN AC-48100 (Al-17Si-4Cu-Mg) Alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, Al-17Si-4Cu-0.6Mg-0.2Ti which is based of the EN AC-48100 alloy, Al-17Si-4Cu-0.6Mg0.2Ti-1Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-2Zn, Al- 17Si-4Cu-0.6Mg-0.2Ti-3Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-4Zn and Al-17Si-4Cu-0.6Mg-0.2Ti-5Zn ... -
Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes
(Elsevier, 2021)Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes is experimentally investigated. The cross sectional ratios in the evaporator and condenser sides are different from each other, ... -
Effect of fin width ratio on thermal performance of fin based-heat sink with phase change materials
(Elsevier, 2023)The rapid development of electronics, coupled with need of miniaturization in the design and manufacture, makes heat dissipation, which is critical for the performance, lifetime, and reliability of the components extremely ... -
Effect of gradually expanding flow passages on flow boiling of micro pin fin heat sinks
(Elsevier, 2022)In this paper, effect of gradually expanding flow passages on saturated flow boiling characteristics of micro pin fin heat sinks is experimentally investigated. In this regard, a comparative analysis is performed based on ... -
Effect of grain refinement with titanium on the microstructure, mechanical and corrosion properties of Al-25Zn alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, one binary Al-25n alloys and eleven ternary aluminum-zinc-titanium alloys, Al-25Zn-0.01Ti, Al-25Zn-0.03Ti, Al-25Zn-0.04Ti, Al-25Zn-0.05Ti, Al-25Zn-0.075Ti, Al-25Zn-0.1Ti, Al-25Zn-0.2Ti, Al-25Zn-0.4Ti, ...
